Simeio/Morpho Install Steps	v1.2 AM 18/02/16

Download installation software from :-

http://mobiledownload.donseed.com/WinApps/SimeioPCM/Simeio Morpho Full Install v1.0.2.23.zip

Morpho Install
==============

*** Before proceeding, if the Morpho USB fingerprint enroller is connected to the PC, disconnect it from the PC

1) Install TeamViewer on PC

2) Copy content of folder "01 Morpho Install" to C:\Morpho

3) Install MorphoKit 5.2 from "c:\Morpho\MorphoKit_5_2" folder - select .Net 4 Framework

	Once this is installed goto "C:\Morpho\MorphoKit\LicenceProtection" and run the
	"SafranMorpho_Licence_Protection_Installer.exe" to install the Morpho Licencing module.

	Goto to "C:\Morpho\MorphoKit\Redist" and install

		DotNetFX40
		vc8redist_x86
		vc10redist_x86

	Goto to "C:\Morpho\MorphoKit\Drivers\MorphoSmart" and install the 64 or 32 (depending on Windows in use)
	the Morpho USB enroller drivers.

4) Run Dos command as Administrator (Run As)

	goto "C:\Morpho\MorphoComponents\Active_MACI\bin" folder
	Register Active_MACI.dll
		Run Dos command as administrator
		cd c:\Morpho\MorphoComponents\Active_MACI\bin
		regsvr32 Active_MACI.dll

5) Connect the Morpho USB Fingerprint enroller to the PC to install the usb drivers

	When the drivers are installed. Go into Morpho Licence Manager and check it shows the MACI & VERIF licences

	*** Note: If above does not show MACI/VERIFY licences then a license file needs to be obtained from Morpho
	for which they need the screenshot of the Morpho License Manager. Send this info to Abaid ASAP.

6) Install Simeio Run Times

	Install Windows Install 4.5 (only Windows XP)
	Install Powershell 1.0 (only Windows XP)
	Install SQL server and management studio - *** once this install is started you may move onto step 7 ***
	Synchronization-v2.1-x86-ENU
	DatabaseProviders-v3.1-x86-ENU
	Encoder_en

7) Hardware Install

	a) Connect a 9V to 16 Volts ± 5% (regulated) 1.5Amp minimum PSU to the Morpho MA500+ fingerprint readers.

	Note: PSU needs to be sourced separately as it is not supplied with the readers.

	b) Connect the RJ45 ethernet cable to the reader and run it to the router or PC directly.

	c) Mount the reader and power it up.

	d) Go into Admin mode on reader (Press the keys ".", Red, "." and enter 12345 and press Green key
	   followed by Yellow key.

	e) Select option 2 - Settings, 2 - Easy Setup, Enter 12345, Green Key, Yellow Key.

	f) When prompted "Easy Setup" press Green Key and select option :-
		1) English
		2) On date and time setup, just press Green Key
		3) Select DHCP option based on how the IP address will be assigned to the readers
		4) For the "Do you want to use identification" prompt select "Yes"
		5) No for DESFire 3DES cards, DESFire AES, MIFARE classic
		6) On Interface Parameters and Password select option 4 Next
		7) Select option to reboot reader

	g) If only one reader is connected to the PC then you should now be able to ping the reader on its
	   default IP address of 134.1.32.214 from the PC.

8) Morpho MA500+ fingerprint reader configuration

	Goto to c:\Morpho\MATM Express 7.0.12 folder to configure MA Terminals
	Run MATerminalManagement.exe and enter the IP address of the reader
	Read terminal config
	Set App\Modes\Time Mask = 1
	Set App\Modes\Idle Timeout = 15
	Set App\Modes\Time and Attendance = 1
	Set App\bio ctrl\authent PK contactless = 0
	Set App\bio ctrl\identification = 1
	Write config

9) Install Simeio Application

	Run Setup.exe
	Run Simeio application and enter registration code (obtain this from Abaid)
	In Admin option select project
	In Readers option setup the IP addresses (default if it hasn't been changed 134.1.32.214) with port 11010